yzf 600 swingarm...spools? and recommend me bike stands

[haunter]

I dont have mine in front of me here at work, obviously

is it set up for spools?

guess I could get it setup for spools......


I need a set of stands, front triple tree and rear stand

the SV has spools on the swingarm.......

I'm not super worried about it working with the SV yet, I can order a pin for it later when I need one, and can take the upper off to ensure fitment without breaking plastics

[sweekster]

No spools on the YZF arm.

[reelrazor]

I have a set of these and have used them for five years for everything from HD sportsters and softails to an '05GSXR1000;

http://www.handyindustries.com/shop/pro ... 67&D=5&S=0

You can specify spool or pad, or get both for a little more$.

And the 'tree stand:

http://www.handyindustries.com/shop/pro ... 40&D=1&S=4

I also have an air lift table from them, and the stands are stable enough to put under the bikes on the table.

[haunter]

thanks razor!

they look not too bad, I might get the LP front from kneedraggers(its cheaper than the handy) and get the handy SET, as their set of fork/swingarm is cheaper than the vortex I found.

its cheaper overall to do it that way AND get an extra front fork stand.

[haunter]

/ordered

FYI these are for the 600 for work/winter storage, she also got a FP kit ordered last week. So shes not going unloved !~

[95FZR600]

I have them on mine. Na nan na!

[reelrazor]

thanks razor!

they look not too bad, I might get the LP front from kneedraggers(its cheaper than the handy) and get the handy SET, as their set of fork/swingarm is cheaper than the vortex I found.

its cheaper overall to do it that way AND get an extra front fork stand.

i think you'll be happy.

Yeah, back when I bought mine, Handy had a three pack special-was like $169 or something fro treestand, fork stand and swinger stand. Ive only had one bike that gave me any issues with the rear stand (excluding single sided swingarms and *some* shafties) and that was a Yamaha Warrior...the rear end was too wide, so I stood on one side of the rear stand and stretched it open a bit more.

* i did make a custom dropped pad that allows me to have the rear stand unequal height (side to side) and lift on the shaft drive on one side and arm on the other.

[haunter]

nice.


95 my other bike has spools already so there!

[95FZR600]

nice.


95 my other bike has spools already so there!

I hear ya! My other bike doesn't.

[PIMPMYFZR]

i have an lp rearstand , and i got it for 20 bucks of some chinese dude that was using it to restore vintage jap bikes . it fit perfect for my fzr and streched it out a tiny hair for my yzf swingarm ..so you should be all set .. i really dig those pitbull stands ..

[haunter]

yeah my buddy has pitbulls


one was in our garage during a fire

it still works fine even though its super charred

[yamaha_george]

yeah my buddy has pitbulls


one was in our garage during a fire

it still works fine even though its super charred

H,
I bought my triple tree stand from a local bike shop & am in the process off making the pin & stop longer to clear the fairing of my 600, the rear end paddock stand I made out of s/steel tube scrap and it fits all my RD's & my 600.

see:- http://www.saltmine.org.uk/fzr/paddockstand.html

Just finished welding the jack bobbin holders on the 3HE swing arm while it is off and being cleaned up for storage, my 3TJ was already fitted and i fitted fixings for bobbns on the two 1WG's arms i have.

UK guys one of the 1WG's will be up for sale soon as will the 3EN ( the braced 400 arm with custom stainless steel chain guard )

see:- http://www.saltmine.org.uk/fzr/swingarm.html


As a side note I am busy writing up the 3TJ swing arm swap to take 3HE wheel OR the 3TJ wheel with 1WG sprocket holder. watch out for the announcement