To break or not to break........

FZR250 Forum

Moderators: Site Director, FZR Forum Moderators

Post Reply
SouthendChris
Level 2.0
Level 2.0
Posts: 224
Joined: Sat Oct 15, 2011 2:14 pm
Location: Essex, UK

To break or not to break........

Post by SouthendChris »

I bought a little FZR250RR unseen as I have been after a replacement engine/carb setup for my 50K Km+ 3LN3 bike. I knew it was accident damaged to the LHS and an 'engine casing was shot'.

In for a surprise I was! Turns out its a 1989 3LN1 with 14K Km on the clock. Now knowing the reg number I have traced that it was imported to the UK in 1999 and last taxed for road use in 2002!

All the front fairings are shot, the forks have rust pits so would need new stanchions and indeed the starter clutch housing is foobarred. However the mileage looks genuine and otherwise it looks all there, unmolested and pretty damn good. I drained & whipped the tank off and the fuel filter. With a fresh battery and fuel she was running in 10 minutes. the carb linkages were sticky so the revs didnt die down quick. Oil came from the hole in the sprag clutch casing so no chance to run it upto temp.

To damn good to break :headscratch: Front fairings only fit for the bin, new stanchions, seals and front break pads would be needed plus left handlebar

Image

Image

Image

10 years of dust build up. Clocks frame and horn looked like with a scrub up.

Image

Image

Image

Image

Ah! That'll be the damaged casing then, yes oil did come out of it :duh:

Image

Image

Original stickers (and more) still all over it.

Image

Image

Image

Image

Image

If I knew I could get replacement fairings for reasonable ££££ I would seriously consider recommisioning it. I love these little 250's and this one shouldn't have the hole at 14k rpm my one has :grinnod:

Chris
1990 3LN3 FZR250 - back in safe hands :)
https://farm6.staticflickr.com/5782/227 ... 41e9_b.jpg
1994 3HE FZR600 - R.I.P. 10/01/12

3x RG80 Gamma :)
User avatar
GreyImport
Level 2.0
Level 2.0
Posts: 233
Joined: Fri Jun 22, 2012 3:07 am
Location: Sunny Australia

Re: To break or not to break........

Post by GreyImport »

Snowing over there is it?? :whistle

Apart from the obvious damage that just needs some spit and polish!

I wish mine had been that good when I got it! :grinnod:

My forks were rust pitted but a scrub with steel soap pads and a good polish sorted that :thumbsup:

save me , save me! :notworthy:


Make an offer! lol
http://www.ebay.com.au/itm/Yamaha-FZR25 ... 484ce9c9d6
1990 FZR250R 3LN1
1977 Triumph Bonneville 750 T140V
Image

Image
http://2fiftycc.com/index.php
EMAIL: greyimport@2fiftycc.com

LiteTek Carburettor Seal Kits
http://www.litetek.co/index.html
SouthendChris
Level 2.0
Level 2.0
Posts: 224
Joined: Sat Oct 15, 2011 2:14 pm
Location: Essex, UK

Re: To break or not to break........

Post by SouthendChris »

I just got this one

http://www.ebay.co.uk/itm/300820332550

My first aim is to get the motor running and up to temp - get the fan kicking in. If it dont grumble or leak then all is good. I've ordered an oil filter and I have some new oil in the shed already. Going to get a price on the fork stanchions.... :Kick

EDIT: Fork stanchions 3LN-23110-00 are £139 inc VAT each........ouch lol

And that snow......is made of soap suds! :rofl:

Chris
1990 3LN3 FZR250 - back in safe hands :)
https://farm6.staticflickr.com/5782/227 ... 41e9_b.jpg
1994 3HE FZR600 - R.I.P. 10/01/12

3x RG80 Gamma :)
KaspenOne
100+ Posts
100+ Posts
Posts: 130
Joined: Sun Nov 25, 2012 4:48 am
Location: Santa Maria, California
Contact:

Re: To break or not to break........

Post by KaspenOne »

if you need plastics you can find them on ebay! not that expensive for the whole kit about 400 bucks
Sal Co-Owner of SisBro Motowerkz, Santa Maria
Pacific Coast Riderz -Vice President- Santa Maria Chapter
1996 Yamaha Fzr 600
UNI Air Filter, FP 1.0, R6 header danmoto exhaust,
Orbit Chain 530 with JT Sprocket Set -1 front/+2 rear
Racetech Front suspension
Bridgestone BT-014 120/70/17 & 150/60/18
http://www.facebook.com/Salvador.Leal.Jr
http://www.youtube.com/user/KaspenOne
http://www.facebook.com/pages/Pacific-C ... 9453630808 & http://www.facebook.com/pcr805
SouthendChris
Level 2.0
Level 2.0
Posts: 224
Joined: Sat Oct 15, 2011 2:14 pm
Location: Essex, UK

Re: To break or not to break........

Post by SouthendChris »

If its the chinese fairings, I have seen the 2KR ones and the 3LN3 ones with the projector headlamp - but not the 3LN1 version with the two separate headlamps.

If you have a link post it!!

Was thinking about these http://www.ebay.co.uk/itm/280762052135 and using the original rear light and light panel. I would have to fit the subframe and headlight from my 3LN3 then.

Chris
1990 3LN3 FZR250 - back in safe hands :)
https://farm6.staticflickr.com/5782/227 ... 41e9_b.jpg
1994 3HE FZR600 - R.I.P. 10/01/12

3x RG80 Gamma :)
User avatar
_Will_
Level 5.5
Level 5.5
Posts: 584
Joined: Tue Aug 18, 2009 10:45 pm
Location: USA

Re: To break or not to break........

Post by _Will_ »

reading up some looks like you've found yourself another fun little toy, came across this while looking them up

http://www.youtube.com/watch?v=wGhDlAFn5S8
User avatar
GreyImport
Level 2.0
Level 2.0
Posts: 233
Joined: Fri Jun 22, 2012 3:07 am
Location: Sunny Australia

Re: To break or not to break........

Post by GreyImport »

1990 FZR250R 3LN1
1977 Triumph Bonneville 750 T140V
Image

Image
http://2fiftycc.com/index.php
EMAIL: greyimport@2fiftycc.com

LiteTek Carburettor Seal Kits
http://www.litetek.co/index.html
SouthendChris
Level 2.0
Level 2.0
Posts: 224
Joined: Sat Oct 15, 2011 2:14 pm
Location: Essex, UK

Re: To break or not to break........

Post by SouthendChris »

Excellent link! I am due a bit of ££ this summer so I may leave it tucked in the shed and wait for a few bits to turn up lol. Engine cover arrived today so I gave it a quick rub down and painted it. Will drain the fluids at the weekend and fit it.

Chris
1990 3LN3 FZR250 - back in safe hands :)
https://farm6.staticflickr.com/5782/227 ... 41e9_b.jpg
1994 3HE FZR600 - R.I.P. 10/01/12

3x RG80 Gamma :)
SouthendChris
Level 2.0
Level 2.0
Posts: 224
Joined: Sat Oct 15, 2011 2:14 pm
Location: Essex, UK

Re: To break or not to break........

Post by SouthendChris »

I have finally found what I'm lookin for :headbang:

http://www.ebay.co.uk/itm/281119112623

A replacement set in original colours WOOT

Better start saving for the new stanchions now. Expect a strip and rebuild thread. Still looking for another 3LN3 engine for the sump though.....

Chris

*edit* just ordered them, seller was happy enough to swap the front mudguard for a clear screen - mine is clean enough. This means I gotta start sooner than I though lol :duh:
1990 3LN3 FZR250 - back in safe hands :)
https://farm6.staticflickr.com/5782/227 ... 41e9_b.jpg
1994 3HE FZR600 - R.I.P. 10/01/12

3x RG80 Gamma :)
SouthendChris
Level 2.0
Level 2.0
Posts: 224
Joined: Sat Oct 15, 2011 2:14 pm
Location: Essex, UK

Re: To break or not to break........

Post by SouthendChris »

The Chinese fairings have arrived! Pics to follow.

I have had the rear swingarm out and regreased every suspension bearing. I know the mileage is low but this bike is going to my dad now and he'll use it till he hangs his boots up no doubt, so I'd rather do them for my peace of mind!

Got the exhaust headers off too. No snapped studs but 6 of 8 came out with the nuts! new studs, nuts and ex gaskets ordered (part number has changed by the way!). While the headers were off I took the chance to change the oil filter as it goes in from the bottom of the sump. Upped the preload on the shock to 5/7. Stripped the rear caliper, cleaned all the gunk out of the seal housings and lubed with red grease. The rear master cylinder is next. Got a new chain but waiting for new sprockets/tyres to fit.

Gonna have to sort out the rust in one of the two tanks I have soon :yuck:

Chris
1990 3LN3 FZR250 - back in safe hands :)
https://farm6.staticflickr.com/5782/227 ... 41e9_b.jpg
1994 3HE FZR600 - R.I.P. 10/01/12

3x RG80 Gamma :)
User avatar
GreyImport
Level 2.0
Level 2.0
Posts: 233
Joined: Fri Jun 22, 2012 3:07 am
Location: Sunny Australia

Re: To break or not to break........

Post by GreyImport »

Good progress there :thumbsup:

Ill be interested in seeing how the new fairings look :headbang:
1990 FZR250R 3LN1
1977 Triumph Bonneville 750 T140V
Image

Image
http://2fiftycc.com/index.php
EMAIL: greyimport@2fiftycc.com

LiteTek Carburettor Seal Kits
http://www.litetek.co/index.html
Post Reply