sliders?

blackfzr1000 · Post by **blackfzr1000** » Wed Jul 16, 2008 10:32 pm

Is there anyway to put sliders on my fzr1000? i was thinking about replacing some of the fairing bolts with a slider has anyone done this??

tommyj27 · Post by **tommyj27** » Thu Jul 17, 2008 7:48 am

Not a bad idea, just don't use the same attachment points (drill new?) cuz your sliders won't last a second if you have to use them. maybe use the holes in the frame that are already there to access the float drain screws (600 has them, i'm assuming the 1000 does too).

noshoes · Post by **noshoes** » Mon Jul 21, 2008 9:57 am

I got a set on e-bay from England for under $35 like 2 years ago..Heres a photo..

yamaha_george · Post by **yamaha_george** » Mon Jul 21, 2008 12:24 pm

noshoes wrote:I got a set on e-bay from England for under $35 like 2 years ago..Heres a photo..

Hi,
The PO of my 600 fitted sliders but it did not help save his fairings which is why the bike is now mine :-}

ShogunTX · Post by **ShogunTX** » Mon Jul 21, 2008 12:31 pm

That looks like a skateboard wheel, someone suggested bolting it to the frame, that sounds like the best route. The fairing mounts seem weak

noshoes · Post by **noshoes** » Mon Jul 21, 2008 12:51 pm

They go off the frame.. Photos..

yamaha_george · Post by **yamaha_george** » Mon Jul 21, 2008 1:02 pm

ShogunTX wrote:That looks like a skateboard wheel, someone suggested bolting it to the frame, that sounds like the best route. The fairing mounts seem weak

S,
They look to be the same material as my rear jack stands wheels which I nicked of the eldests skate board.
They are as soft and dig in when sliding on the side perhaps if we used the wheel the way it was meant with bearings ......... where is Mod King when you need him :-}

noshoes · Post by **noshoes** » Mon Jul 21, 2008 1:57 pm

its looks to be made of the same stuff they use to make the handles on snap-on screwdrivers...pretty much bowling ball material.....
RRBike

Post by **ragedigital** » Mon Jul 21, 2008 2:07 pm

Holy crap! NOSHOES - glad to see you posting!

Now, back to your regularly scheduled debate....

yamaha_george · Post by **yamaha_george** » Mon Jul 21, 2008 2:12 pm

noshoes wrote:its looks to be made of the same stuff they use to make the handles on snap-on screwdrivers...pretty much bowling ball material.....

Hi,
Yup but a better material is the modern white stuff they use on dirt bike chain guide/ swing arm protector which seems to be able to take serious abuse and may actually slide and not stick in and spin the bike

Some where I have the tech name for it

Post by **ragedigital** » Mon Jul 21, 2008 2:14 pm

yamaha_george wrote: Some where I have the tech name for it

Delrin?

noshoes · Post by **noshoes** » Mon Jul 21, 2008 2:22 pm

ragedigital wrote:

Holy crap! NOSHOES - glad to see you posting!

Now, back to your regularly scheduled debate....

Hey Rage nice site you have here..I'll try to add what I can when I can......
RRBike

FZRSupport: the FZROnline Archive

sliders?

sliders?

Re: sliders?

Re: sliders?

Re: sliders?

Re: sliders?

Re: sliders?

Re: sliders?

Re: sliders?

Re: sliders?

Re: sliders?

Re: sliders?

Re: sliders?