My FZR project is almost complete!!!! Comments please

[Target30]

Looks great dude, i love the color scheme too, really nicely done.

[stealth66]

Thanks man. You got a nice one too. Took me a litle while to learn where your front fairing came from. I wasn't trying to make an "FZR6" . I forget, do you have a different motor in it?

[stealth66]

Oh damn i guess i should have erased them . I'm in south jersey, washington twp. I made the coolant bottle out of PVC. It was easy. I'll take some pictures and post them. Thanks for the comments.

[tampaFZR600]

so what size wheel is the 1000?? The yzf swing fits a 200 tire?! What sprocket did you run for the front?

[sweekster]

so what size wheel is the 1000?? The yzf swing fits a 200 tire?!

89-95 1000 rear wheel is 5.5x17...and apparently, yes it fits.

[Genesis]

Took me a litle while to learn where your front fairing came from.

it came from washington
He did do a very nice job.

[stealth66]

Yeah it took me a while to put it all together but being as a YZF600 swinger is a fairly easy swap and would give you a 5" rear wheel, i began to look on the YZF sites to see if they tried fitting anything wider. I discovered the FZR1000 was a direct bolt on. The only thing i changed was the torsion bar and caliper mounting bracket. The wheels are hard to find though. 89-95 is correct. Its a 200-50-17 and it barely fits but no rubbing

[stealth66]

Oh and the sprocket setup is a 520 14T for a ZX6R 03+ (offset about 8mm) and the rear is the stock YZF600 47T turned around backwards. With a standard 530 chain, it lines up so perfectly you'd think it was meant to be. Plus, with the 14T and the 47T in the back, its the equivalent to a quick accel kit with a 17" wheel!

[tampaFZR600]

Oh and the sprocket setup is a 520 14T for a ZX6R 03+ (offset about 8mm) and the rear is the stock YZF600 47T turned around backwards. With a standard 530 chain, it lines up so perfectly you'd think it was meant to be. Plus, with the 14T and the 47T in the back, its the equivalent to a quick accel kit with a 17" wheel!

yea thats exactly what i'm doing right now, viewtopic.php?f=30&t=3123
have that exact front sprocket and i have a jt 530 47t sprocket that i got with the complete yzf swingarm? This 5" YZF wheel is winnie . I'll be looking into this for sure!

[tampaFZR600]

.......but if you used the stock rear sprocket, isn't that a 530 sprocket?

[XxxYoOoOxxX]

Hey man what type of "Undertail" did you use?

[stealth66]

Thanks guys. Yeah your stock rear sprocket is for a 530 chain (YZF and FZR) but they're not interchangeable. However, if you come across an FZR1000 wheel, the YZF sprocket is interchangeable with that. stock or aftermarket rear sprocket from the YZF will do just fine (i turned my around backwards to get better lineup). 47t would be the equilalent to the FZR600 quick accel with the 14T front.

[stealth66]

The undertail i used is from an 02 R6. The plate mounts are shaved. 99-02 tails are the same but the 02 undertail is different. It wasn't easy but i think it looks much nicer than the 99 undertail/taillight setup.

[mxryder21]

That bike is one of the "cleanest" fiZzers i've seen. I think the paint scheme is b!tchin'. Killer work bro!!

[stealth66]

Thanks a lot man!