Clutch slipping?

FZR600 Forum

Moderators: Site Director, FZR Forum Moderators

Post Reply
User avatar
mszilves
Level 1.5
Level 1.5
Posts: 151
Joined: Fri May 09, 2008 1:52 pm

Clutch slipping?

Post by mszilves »

Hey guys, had the strangest experience on my bike this morning going to work. I was in 4th, cruising at around 5K RPM, when I got to a straight strectch I couldn't resists opening her up a bit. So I cranked the throttle hard, and the bike starts to take off. Nice and crisp, quick acceleration. When it hit around 8000RPM, the engine just "jumped" to around 9500RPM with the bike still maintaining the same speed, if that makes sense. At the time, I couldn't really think what that could be, but then I started to think about it, and most likely it was my clutch? I hope it's not transmission, but it didn't make any tranny noise... Can anyone confirm it's the clutch, or experienced anything similar?

No issues with my clutch, and the friction plates are new as of beginning of last season.

Since we're basically running a 400 bottom end on our 600s, I guess we're pretty close to the limits?
Last edited by mszilves on Mon Sep 08, 2008 1:19 pm, edited 1 time in total.
ImageImage

'03 Liquid Silver R6
'91 FZR 600
'97 Forks w/ .85kg/mm Race Tech springs, Gold-Valve Emulators (2 turns), 20w fork oil / Fox Twin Clicker
R6 front calipers and master cylinder, R6 tail
YZF swingarm conversion
'01 R1 Digital Cluster conversion
K&N Drop-In, Factory Pro emulsion tubes, stock 5CFZ4 needle on clip 2, 22mm floats, mixture screws temp tuned
Bridgestone BT-016s 110/170


Image
bweight
Level 4.0
Level 4.0
Posts: 421
Joined: Wed May 07, 2008 4:03 pm
Location: Sudbury, ON, Canada

Re: Clutch slipping?

Post by bweight »

Sounds to me like it was the clutch, but I suppose I could be wrong. Did you try it again to see if it happened once more?
89 FZR 400
Custom Paintjob
600 plastics.
06 - R6 Shock
FZR600 Motor
Polished Frame & Engine Covers

Soon to be:
Broke........

Image
FZROnline.com Decals. Get yours Now!!!
User avatar
mszilves
Level 1.5
Level 1.5
Posts: 151
Joined: Fri May 09, 2008 1:52 pm

Re: Clutch slipping?

Post by mszilves »

bweight wrote:Sounds to me like it was the clutch, but I suppose I could be wrong. Did you try it again to see if it happened once more?
Yeah, tried it again at lunch today, and seemed to do it again. But intermittent. Only did it once, and this time I think in 3rd. It definitely doesn't do it often, and now that I remember, I'm pretty sure it's done it a couple times before, I just never really payed attention. But it's definitely only on full throttle around 8K RPM.
ImageImage

'03 Liquid Silver R6
'91 FZR 600
'97 Forks w/ .85kg/mm Race Tech springs, Gold-Valve Emulators (2 turns), 20w fork oil / Fox Twin Clicker
R6 front calipers and master cylinder, R6 tail
YZF swingarm conversion
'01 R1 Digital Cluster conversion
K&N Drop-In, Factory Pro emulsion tubes, stock 5CFZ4 needle on clip 2, 22mm floats, mixture screws temp tuned
Bridgestone BT-016s 110/170


Image
User avatar
haunter
2000+ Posts
2000+ Posts
Posts: 2266
Joined: Fri May 09, 2008 9:17 am
Location: Urbana, Il USA
Contact:

Re: Clutch slipping?

Post by haunter »

what oil are you running?
User avatar
R3TARD
Level 4.5
Level 4.5
Posts: 491
Joined: Thu May 22, 2008 7:07 pm
Location: north Georgia
Contact:

Re: Clutch slipping?

Post by R3TARD »

from my experience it breaks down pretty much to one of these

worn clutch
bike not warmed up
wrong oil
too much oil
low on oil

Your transmission is Gears so if that baby slips you would damn sure know it LOL

or....... your clutch was just tired, hung over from the weekend, or just plain lazy feeling.. J/K

it is getting a tad cooler even here in GA so maybe your bike wasnt warmed up all the way, or low on oil.

1992 FZR 600
Yoshi exhaust
K&N pods
Airtech R1-kit
02 R6 fork swap
02 R6 Swingarm
520 chain conversion
07 R6 controls
Vortex R6 clipons
07 R6 radial master


2003 CBR 600rr
bone stock
Post Reply