====== Carburetors ======
==== How it works ====
FIXME

==== Removing ====
**Time:** //30 minutes if you're fast//\\
**Instructions:**
  - Remove Seats
  - Remove tank cover
  - Remove airbox
  - Remove gas tank
    - Turn gas tank to the off position.
    - Use a pair of pliers to disconnect the fuel line (its red) from the carbs.\\ :!:Get a cup as some gas will come out of the fuel line. :!:
    - Remove the fuel valve key. (remove the screw and pull it off)\\ :!:If you don't do this your tank will get stuck on its way out.:!:
    - Remove the two tank holders that are bolted into the frame. (you need a 10mm and 12mm socket wrench)
    - Carefully pull up on the tank place on the floor.
  - Use a 3mm allen key and loosen the intake manifold boots.  (go buy a set of allen key socket wrenches as its much easier)
  - Remove the choke from the frame.
  - Remove the throttle cables from the carbs.  pull the throttle to give you some leverage.  You will also need a 10mm wrench.
  - Now stand over your bike and pull the carbs out.  You need to rock them back and forth to get them out.
  - There will still be gas in the carbs so you need to empty it. If you go outside and turn them upside down a few times it usually gets everything out.

- icontender
      

==== Throttle cables ====
FIXME

==== Jetting ====
FIXME\\ 

{{:fzr600_dynojet_factory_pro_needles.jpg?300|Click To Enlarge}}
{{:fzr600_dynojet_needle_assembly.jpg?300|Click To Enlarge}}
{{:fzr600_carb_main_jet_ims_identification.jpg?300|Click To Enlarge}}
{{:fzr600_emulsion_tube_alignment.jpg?300|Click To Enlarge}}
{{:fzr600_emulsion_tube_identification.jpg?300|Click To Enlarge}}
{{:carb-1.jpg?300|Click To Enlarge}}
{{:fzr600_inserting_spring_into_diaphragm_assembly.jpg?300|Click To Enlarge}}
{{:fzr600_inserting_diaphragm_assembly.jpg?300|Click To Enlarge}}
{{:fzr600_inserting_needle_into_emulsion_tube.jpg?300|Click To Enlarge}}
{{:fzr600_inserting_the_block_jet_assembly.jpg?300|Click To Enlarge}}
==== Syncing ====
FIXME

[[http://fzronline.com/forum/viewtopic.php?f=8&t=5924]]

Placed here by Y_G until he gets a chance to edit this properly 2010-04-03

[[http://fzronline.com/forum/viewtopic.php?f=21&t=6089]]
A picture is worth 1000 words.(Carb Sync Tool)(Feel free to edit or use pictures)

[[http://www.allthingsmoto.com/forums/f-15/how-set-your-motorcycle-carburetor-float-level-more-commentary-13608/]]
An explanation of float height setting with tech terms explained 

==== Idle Adjustment ====
In this photo, you can clearly see the idle adjust screw - top left. It has the flex area covered in the black plastic sheathing.\\ 

*Note: These are Cali carbs and have 2 tubes shown on the right that may or may not be like your bike. I removed and plugged those holes.\\ 

Turning the idle adjust screw clockwise will increase idle RPM's and counter clockwise will decrease rpms\\ 

{{:fzr600_idle.jpg?300|Click To Enlarge}}

==== VIDEOS ====

=== FZR600 carburetor cleaning (by match417) ===
{{youtube>small:k5R5XBI-I9U}}

=== Drilling out EPA caps (by match417) ===
{{youtube>small:qu3-3-RqDy4}}

=== Bench sync FZR600 carbs (by match417) ===
{{youtube>small:rUJUNG7sMfI}}


[[http://fzronline.com/forum/viewtopic.php?f=32&t=1098|{{  :comments.gif  |CLICK HERE}}]]