FZR600/YZF600/R6 Build
Moderators: Site Director, FZR Forum Moderators
Re: FZR600/YZF600/R6 Build
This is the FZR1000 bracket If you are doing the YZF600 tank swap, this is a great way to go
I used the FZR1000 rear tank mount, But it required heavy modification, I will get a better pic of it later. It will work very will though. Now I am trying to figure out how to hold the front of the r6 seat in place.
1990 Yamaha FZR600 Genesis, Daily Driver
My FZR6 Rebuild
1985 GMC 4x4 T-15 X-Cab Sierra
1999 Chevy 4x4 Blazer (wifes car)
"If a man can build it, I can take it apart and sometimes even put it back together and fix it" --Unknown
"'I wish none of this had happened.' 'So do all who live to see such times. But that is not for them to decide. All we have to decide is what to do with the time that is given to us.....'" J.R.R. Tolkien
My FZR6 Rebuild
1985 GMC 4x4 T-15 X-Cab Sierra
1999 Chevy 4x4 Blazer (wifes car)
"If a man can build it, I can take it apart and sometimes even put it back together and fix it" --Unknown
"'I wish none of this had happened.' 'So do all who live to see such times. But that is not for them to decide. All we have to decide is what to do with the time that is given to us.....'" J.R.R. Tolkien
Re: FZR600/YZF600/R6 Build
Little Update, I have the tank pretty much done, Now I just have to make a bracket for my fuel pump and figure out the airbox, sorry no pictures of that yet.
I am also starting on the r6 radiator project. Since my filler neck bracket broke off, and I wanted to relocate the fill neck to a little more accessable location I am putting on a 05 R6 radiator. But first since I don't really have any where to attach it, being "long bolts" throught the gusset at the front bottom side of the frame like the 400 frame. I oppted to make a conversion bracket. so hopefully with luck I can take this.
Using this.
And make this.
I am also starting on the r6 radiator project. Since my filler neck bracket broke off, and I wanted to relocate the fill neck to a little more accessable location I am putting on a 05 R6 radiator. But first since I don't really have any where to attach it, being "long bolts" throught the gusset at the front bottom side of the frame like the 400 frame. I oppted to make a conversion bracket. so hopefully with luck I can take this.
Using this.
And make this.
Last edited by Genesis on Thu Jun 18, 2009 6:34 pm, edited 1 time in total.
1990 Yamaha FZR600 Genesis, Daily Driver
My FZR6 Rebuild
1985 GMC 4x4 T-15 X-Cab Sierra
1999 Chevy 4x4 Blazer (wifes car)
"If a man can build it, I can take it apart and sometimes even put it back together and fix it" --Unknown
"'I wish none of this had happened.' 'So do all who live to see such times. But that is not for them to decide. All we have to decide is what to do with the time that is given to us.....'" J.R.R. Tolkien
My FZR6 Rebuild
1985 GMC 4x4 T-15 X-Cab Sierra
1999 Chevy 4x4 Blazer (wifes car)
"If a man can build it, I can take it apart and sometimes even put it back together and fix it" --Unknown
"'I wish none of this had happened.' 'So do all who live to see such times. But that is not for them to decide. All we have to decide is what to do with the time that is given to us.....'" J.R.R. Tolkien
Re: FZR600/YZF600/R6 Build
additional pictures for those of you that are doing the R6 tail.
http://www.jeffersandkristi.com/html/r6 ... rsion.html
http://www.jeffersandkristi.com/html/r6 ... rsion.html
1990 Yamaha FZR600 Genesis, Daily Driver
My FZR6 Rebuild
1985 GMC 4x4 T-15 X-Cab Sierra
1999 Chevy 4x4 Blazer (wifes car)
"If a man can build it, I can take it apart and sometimes even put it back together and fix it" --Unknown
"'I wish none of this had happened.' 'So do all who live to see such times. But that is not for them to decide. All we have to decide is what to do with the time that is given to us.....'" J.R.R. Tolkien
My FZR6 Rebuild
1985 GMC 4x4 T-15 X-Cab Sierra
1999 Chevy 4x4 Blazer (wifes car)
"If a man can build it, I can take it apart and sometimes even put it back together and fix it" --Unknown
"'I wish none of this had happened.' 'So do all who live to see such times. But that is not for them to decide. All we have to decide is what to do with the time that is given to us.....'" J.R.R. Tolkien
Re: FZR600/YZF600/R6 Build
UPDATE, I finally feel like I am getting somewhere:
mockup of tail
Rear Tank Mounting, You can see I used the Fzr mount for the front of r6 seat, and the Fzr1000 mount for the rear of the tank.
Undertail Mounting, I love the nutsert tool I picked up at HF. worth the $16.
mockup of tail
Rear Tank Mounting, You can see I used the Fzr mount for the front of r6 seat, and the Fzr1000 mount for the rear of the tank.
Undertail Mounting, I love the nutsert tool I picked up at HF. worth the $16.
1990 Yamaha FZR600 Genesis, Daily Driver
My FZR6 Rebuild
1985 GMC 4x4 T-15 X-Cab Sierra
1999 Chevy 4x4 Blazer (wifes car)
"If a man can build it, I can take it apart and sometimes even put it back together and fix it" --Unknown
"'I wish none of this had happened.' 'So do all who live to see such times. But that is not for them to decide. All we have to decide is what to do with the time that is given to us.....'" J.R.R. Tolkien
My FZR6 Rebuild
1985 GMC 4x4 T-15 X-Cab Sierra
1999 Chevy 4x4 Blazer (wifes car)
"If a man can build it, I can take it apart and sometimes even put it back together and fix it" --Unknown
"'I wish none of this had happened.' 'So do all who live to see such times. But that is not for them to decide. All we have to decide is what to do with the time that is given to us.....'" J.R.R. Tolkien
- shredex
- 2000+ Posts
- Posts: 2768
- Joined: Sun Sep 07, 2008 10:40 am
- Location: Holiday, Florida
- Contact:
Re: FZR600/YZF600/R6 Build Updated 6-26-09
thats what im talking about!
you need a gold USD fork swap as well!
you need a gold USD fork swap as well!
Re: FZR600/YZF600/R6 Build Updated 6-26-09
I just got these and Hope to make them into running lights/turn signals.
Two Wire to Three Wire Conversion Write-up
Does anyone know what you have todo to eliminate the rapid blinker syndrome?
I am also going with the LED tail lights/brake lights.
http://www.ledlight.com/1156-1157-autom ... ights.aspx
should look pretty good w/ everything being red in the back.
Two Wire to Three Wire Conversion Write-up
Does anyone know what you have todo to eliminate the rapid blinker syndrome?
I am also going with the LED tail lights/brake lights.
http://www.ledlight.com/1156-1157-autom ... ights.aspx
should look pretty good w/ everything being red in the back.
1990 Yamaha FZR600 Genesis, Daily Driver
My FZR6 Rebuild
1985 GMC 4x4 T-15 X-Cab Sierra
1999 Chevy 4x4 Blazer (wifes car)
"If a man can build it, I can take it apart and sometimes even put it back together and fix it" --Unknown
"'I wish none of this had happened.' 'So do all who live to see such times. But that is not for them to decide. All we have to decide is what to do with the time that is given to us.....'" J.R.R. Tolkien
My FZR6 Rebuild
1985 GMC 4x4 T-15 X-Cab Sierra
1999 Chevy 4x4 Blazer (wifes car)
"If a man can build it, I can take it apart and sometimes even put it back together and fix it" --Unknown
"'I wish none of this had happened.' 'So do all who live to see such times. But that is not for them to decide. All we have to decide is what to do with the time that is given to us.....'" J.R.R. Tolkien
Re: FZR600/YZF600/R6 Build Updated 6-26-09
You have to get two 5ohm resistors and put them between the positive and negative wires on each side of the harness. 2 per side. That will get rid of the rapid blink. They get mighty warm though so tuck them out of the way. I'll try and get you a picture of what they look like.
Do YOU Scopper?
"When some people cry, it's not because they’re weak. It’s because they’ve been strong for far too long."
Re: FZR600/YZF600/R6 Build Updated 6-26-09
I can build it....... But know nothing about electronics, would you please give me a Radio Schack part number? or something.thatkid wrote:You have to get two 5ohm resistors and put them between the positive and negative wires on each side of the harness. 2 per side. That will get rid of the rapid blink. They get mighty warm though so tuck them out of the way. I'll try and get you a picture of what they look like.
1990 Yamaha FZR600 Genesis, Daily Driver
My FZR6 Rebuild
1985 GMC 4x4 T-15 X-Cab Sierra
1999 Chevy 4x4 Blazer (wifes car)
"If a man can build it, I can take it apart and sometimes even put it back together and fix it" --Unknown
"'I wish none of this had happened.' 'So do all who live to see such times. But that is not for them to decide. All we have to decide is what to do with the time that is given to us.....'" J.R.R. Tolkien
My FZR6 Rebuild
1985 GMC 4x4 T-15 X-Cab Sierra
1999 Chevy 4x4 Blazer (wifes car)
"If a man can build it, I can take it apart and sometimes even put it back together and fix it" --Unknown
"'I wish none of this had happened.' 'So do all who live to see such times. But that is not for them to decide. All we have to decide is what to do with the time that is given to us.....'" J.R.R. Tolkien
Re: FZR600/YZF600/R6 Build Updated 6-26-09
I was comparing the hacked up r6 harness and my FZR harness, And I think I will try to use some of the newer components.
Last edited by Genesis on Thu Jul 16, 2009 1:29 pm, edited 1 time in total.
1990 Yamaha FZR600 Genesis, Daily Driver
My FZR6 Rebuild
1985 GMC 4x4 T-15 X-Cab Sierra
1999 Chevy 4x4 Blazer (wifes car)
"If a man can build it, I can take it apart and sometimes even put it back together and fix it" --Unknown
"'I wish none of this had happened.' 'So do all who live to see such times. But that is not for them to decide. All we have to decide is what to do with the time that is given to us.....'" J.R.R. Tolkien
My FZR6 Rebuild
1985 GMC 4x4 T-15 X-Cab Sierra
1999 Chevy 4x4 Blazer (wifes car)
"If a man can build it, I can take it apart and sometimes even put it back together and fix it" --Unknown
"'I wish none of this had happened.' 'So do all who live to see such times. But that is not for them to decide. All we have to decide is what to do with the time that is given to us.....'" J.R.R. Tolkien
What are these? and are they swapable?
I was comparing the hacked up r6 harness and my FZR harness, And came accross this,
there is something similar on the r6 harness that combines the main fuse with it
but for the most part are these swapable?
there is something similar on the r6 harness that combines the main fuse with it
but for the most part are these swapable?
1990 Yamaha FZR600 Genesis, Daily Driver
My FZR6 Rebuild
1985 GMC 4x4 T-15 X-Cab Sierra
1999 Chevy 4x4 Blazer (wifes car)
"If a man can build it, I can take it apart and sometimes even put it back together and fix it" --Unknown
"'I wish none of this had happened.' 'So do all who live to see such times. But that is not for them to decide. All we have to decide is what to do with the time that is given to us.....'" J.R.R. Tolkien
My FZR6 Rebuild
1985 GMC 4x4 T-15 X-Cab Sierra
1999 Chevy 4x4 Blazer (wifes car)
"If a man can build it, I can take it apart and sometimes even put it back together and fix it" --Unknown
"'I wish none of this had happened.' 'So do all who live to see such times. But that is not for them to decide. All we have to decide is what to do with the time that is given to us.....'" J.R.R. Tolkien
Re: What are these? and are they swapable?
looks like the starter solenoid....?
93 Yamaha FZR 600 - Track Project
-in NOT AS MANY pieces for track, beater prep
SOLD
88 FZR1000, 90 FZR 1040, 03 Suzuki SV1000S, 06 R6 50th Anniversary
-in NOT AS MANY pieces for track, beater prep
SOLD
88 FZR1000, 90 FZR 1040, 03 Suzuki SV1000S, 06 R6 50th Anniversary
Re: What are these? and are they swapable?
Doesn't it buzz if your battery is too low and you try to start your bike?
Upgrades:
- Barnett Clutch------------------------------------------R6 Blue Dots, Front Master Brake Cylinder+Reservoir
WP Adjustable Rear Shock----------------------------Vortex 520 Conversion with RK GB520GXW Chain
V&H Header (4-1)--------------------------------------Swingarm Spool Mounts
Cobra F1r Exhaust Can--------------------------------R6 Voltage Regulator
Flo-Commander with Remote-------------------------Custom Airtech Passenger Seat
Stage 7 Jet kit with Diffuser Caps--------------------Factory Pro Nickel Emulsion Tubes
Wiseco 630 Kit------------------------------------------Custom Frame Slider Mounts
Modking Hydraulic Clutch Kit--------------------------Hella Projection Headlight with Xentec HID Kit (H9 Bulb)
Modking Aluminum Radiator Overflow Bottle--------
-
- 5000+ Posts
- Posts: 5853
- Joined: Fri May 09, 2008 8:46 am
- Location: west london UK
Re: What are these? and are they swapable?
yup sure does and a solonoid is a solonoid providing it is 12V and the amperage is good.haunter wrote:looks like the starter solenoid....?
Re: FZR600/YZF600/R6 Build Updated 6-26-09
thatkid via PM wrote:totally forgot about the blinker thing so I went and took care of that too. Here are some pictures.Genesis wrote:I can build it....... But know nothing about electronics, would you please give me a Radio Schack part number? or something.thatkid wrote:You have to get two 5ohm resistors and put them between the positive and negative wires on each side of the harness. 2 per side. That will get rid of the rapid blink. They get mighty warm though so tuck them out of the way. I'll try and get you a picture of what they look like.
The two 10 ohm 10W resistors wrapped together with electrical tape. All you have to do is cross them on the positive and negative on each side of the blinkers.
A close up of the numbers.
I picked them up at radio shack for like 5 bucks total. That's all there is to it.
-Nate
1990 Yamaha FZR600 Genesis, Daily Driver
My FZR6 Rebuild
1985 GMC 4x4 T-15 X-Cab Sierra
1999 Chevy 4x4 Blazer (wifes car)
"If a man can build it, I can take it apart and sometimes even put it back together and fix it" --Unknown
"'I wish none of this had happened.' 'So do all who live to see such times. But that is not for them to decide. All we have to decide is what to do with the time that is given to us.....'" J.R.R. Tolkien
My FZR6 Rebuild
1985 GMC 4x4 T-15 X-Cab Sierra
1999 Chevy 4x4 Blazer (wifes car)
"If a man can build it, I can take it apart and sometimes even put it back together and fix it" --Unknown
"'I wish none of this had happened.' 'So do all who live to see such times. But that is not for them to decide. All we have to decide is what to do with the time that is given to us.....'" J.R.R. Tolkien
Re: FZR600/YZF600/R6 Build Updated 6-26-09
These are some close Ups of the modified 1990 FZR1000 rear tank mount and slimed downed FZR seat mount.
Click on the Thumbnails
Click on the Thumbnails
1990 Yamaha FZR600 Genesis, Daily Driver
My FZR6 Rebuild
1985 GMC 4x4 T-15 X-Cab Sierra
1999 Chevy 4x4 Blazer (wifes car)
"If a man can build it, I can take it apart and sometimes even put it back together and fix it" --Unknown
"'I wish none of this had happened.' 'So do all who live to see such times. But that is not for them to decide. All we have to decide is what to do with the time that is given to us.....'" J.R.R. Tolkien
My FZR6 Rebuild
1985 GMC 4x4 T-15 X-Cab Sierra
1999 Chevy 4x4 Blazer (wifes car)
"If a man can build it, I can take it apart and sometimes even put it back together and fix it" --Unknown
"'I wish none of this had happened.' 'So do all who live to see such times. But that is not for them to decide. All we have to decide is what to do with the time that is given to us.....'" J.R.R. Tolkien