exhaust bracket

[PIMPMYFZR]

yea i personally like it too , but im done dumping money into my bike for appearence purposes i wanna swap out my rear wheel and im done wit anymore mods

[yamaha_george]

yamaha george- are they actually fzr600 specific or do you know of any other bikes that interchange? i checked bikebandit and they didn't have any fzr ones, but tons for other bikes.

The one on Ebay is FZR600 specific

I can tell you that those ugly black tube footpeg hangers are a PITA to get a replacement for as they are 100mm centres where most are 80 / 90mm.where they go on the frame.
There is rumour that FZR 400 of ONE model only fit but as of yet I have not found out which it is.

I came across a do-it-yourself end can supplier and their stays had slots the crowd was so thick round the stall I could not get a measurement
see:-


http://www.aa16.co.uk & http://www.aa16.co.uk/a16yamahafzr600.htm

for details
HTH

[Lasse]

There is rumour that FZR-400 of ONE model only fit but as of yet I have not found out which it is.

After a close look in the Yamaha parts list....
I think the FZR-400 aluminium bracket have Yamaha part # : 2TK-21445-00-00




Here in Sweden it today cost : 950 SEK = 82 GB£ = 161 US$ = 168 AU$

[yamaha_george]

There is rumour that FZR-400 of ONE model only fit but as of yet I have not found out which it is.

After a close look in the Yamaha parts list....
I think the FZR-400 aluminium bracket have Yamaha part # : 2TK-21445-00-00

Lasse,
Thanks for the tip

I had two sets 1set I still have that for sure does not fit marked in the casting as :-4JH-S.
The other was sold but damned if i can find the part number different to these still here but again did not fit.

[Lasse]

Here are some pictures on what I think is the Yamaha OEM exhaust bracket for the FZR-400....

The question is : Will it fit the 600 ?

[bweight]

This is my stock 400 rear bracket..




Where I have the exhaust mounted to it used to be where the passenger peg was. I had to gind the tabs where the peg was mounted in order for the V&H can off of a 600 to fit correctly.

Looks different than yours Lasse.. Not sure whether that's an issue of being overseas and having a different version... Mine's an 89, not sure what year the one in your pic is.

Brian

[Lasse]

Where I have the exhaust mounted to it used to be where the passenger peg was.
I had to gind the tabs where the peg was mounted in order for the V&H can off of a 600 to fit correctly.

Brian

Hi Brian

( The bike in the pictures is only for refference purposes ! )


Acording to Yamaha's part list, the FZR-400 came in 2 different versions...

* One version with single seater and a exhaust bracket without a tab for the passenger fot peg. Part # : 2TK-21445-00-00
&
* One version with 2-up seat using a different exhaust bracket made for the passenger fot peg. Part # : 1WG-2742L-00-00


.

[thatkid]

I would be happy to make a few of these for people. You give me a design you want and I'll see if I can fab it up. Not sure what the going rate on these things is but I'm sure I could be competitive.

-Nate

[Lasse]

I would be happy to make a few of these for people.
You give me a design you want and I'll see if I can fab it up.
Not sure what the going rate on these things is but I'm sure I could be competitive.

// Nate

When can I order one from you ?