I didn't know about the 636. Is anyone on here running that setup?abs600fzrr wrote:636 and z1000 shock will fit from what i looked into this summer. high spring rates too...just be prepaired to pay a good price for one.
R1 shock
Moderators: Site Director, FZR Forum Moderators
Re: R1 shock
Re: R1 shock
they'r the cheapest one in ebay on the uk...abs600fzrr wrote:636 and z1000 shock will fit from what i looked into this summer. high spring rates too...just be prepaired to pay a good price for one.
Just have to do a bit of credit crunch anda i''l be set
-
abs929cbrrr
- 1000+ Posts
- Posts: 1171
- Joined: Sun May 11, 2008 12:53 pm
- Location: lebanon pa 17042
- Contact:
Re: R1 shock
on the archives i had specs for all new style bikes mono shocks, they should work but i am not saying they do i just had emails saying dimenions and they matched up kinda good.
02 xr200r set up for XC
96 trx300ex set up for XC
im roadbike less!!!!!!
96 trx300ex set up for XC
im roadbike less!!!!!!
Re: R1 shock
I'd seen it but I wasn't paying to much attention.
I'll have a look at your post.
If it would be a bit a longer and a lot harder it would be cool.
Btw do you guys know it the fork internals from an early R6 would fit the FZR standard forks?
I'll have a look at your post.
If it would be a bit a longer and a lot harder it would be cool.
Btw do you guys know it the fork internals from an early R6 would fit the FZR standard forks?
Re: R1 shock
Degree or not i think you will have to change out the whole bottom of the shock to get it mounted i believe if its going on fzr swingarm .. that might not be worth the cost , but if your not a heavy person you can swap or for r6 or gsxr 600 and probably wont be able to tell the differnce ..and all you need is a couple longer skinnier bolts and washers from local hardware store, you might also try looking into the FZ newer model bike FZ6 or FZR1000 maybe have some luck since those are probably more common in that side of the pond_LM_ wrote:Since i'm finishing a engineering degree i should know
Last edited by PIMPMYFZR on Thu Dec 11, 2008 11:53 am, edited 1 time in total.
2002 R1 9k miles , Hotbodies undertail , Chopped Hindle Hi Mount , Solo Seat cowl,Frame sliders, little yellow yamaha wheel stickers .hehe
94' 600RR SOLD**
hid xenon
airtek solo tail
time for a 1000
R.I.P DaD 2/17/09 Your in my <3 always
Re: R1 shock
im guessing but i believe the r6 would be bigger since the tubes are also bigger ,_LM_ wrote:I'd seen it but I wasn't paying to much attention.
I'll have a look at your post.
If it would be a bit a longer and a lot harder it would be cool.
Btw do you guys know it the fork internals from an early R6 would fit the FZR standard forks?
2002 R1 9k miles , Hotbodies undertail , Chopped Hindle Hi Mount , Solo Seat cowl,Frame sliders, little yellow yamaha wheel stickers .hehe
94' 600RR SOLD**
hid xenon
airtek solo tail
time for a 1000
R.I.P DaD 2/17/09 Your in my <3 always
Re: R1 shock
All models are common here but the part aren't.
R6 shocks are to expensive and I like a challenge (that's why I bought the FZR in the first place).
I think I'll go with the zx6r shock and try to addapt it, I'll keep you posted
R6 shocks are to expensive and I like a challenge (that's why I bought the FZR in the first place).
I think I'll go with the zx6r shock and try to addapt it, I'll keep you posted