Genesis rebuild
Moderators: Site Director, FZR Forum Moderators
Genesis rebuild
I'm starting this to document the rebuild of my new bike. So what better place to start than to show the condition its in currently:
Please note the tasteful application of led strips on the leading edge of the fairing:
More led lighting at the rear:
Whats not seen in the pics is that the park light globes were changed to led's that change colors, between red, blue, green, orange, yellow and green. The frikken thing looked like a Christmas tree on wheels
What used to be polished rims, now gathering rust:
I'm not sure exactly what the po was powering, but he had fitted multi-plug for charging items. Note also the untidy wiring, various rusty items and screen that's been repaired by fiberglass:
Some road rash on the fairing:
Bent footpeg and shift lever. There is also some rust on the sub-frame:
Relatively new chain that is starting to rust as it hasn't been kept lubricated:
Faded taillight, rusted grab rail and torn seat:
Dented and scratched exhaust:
Broken vfr400 mirrors:
Fiberglass repairs to the fairing:
I'm going to be starting with the mechanical's first and when those are sorted moving on to the cosmetics. I've already had the radiator welded and pressure tested, as it was leaking when I bought the bike, next up will be to figure out why the fan isn't switching on.
Hope you enjoy the show
Conrad
Please note the tasteful application of led strips on the leading edge of the fairing:
More led lighting at the rear:
Whats not seen in the pics is that the park light globes were changed to led's that change colors, between red, blue, green, orange, yellow and green. The frikken thing looked like a Christmas tree on wheels
What used to be polished rims, now gathering rust:
I'm not sure exactly what the po was powering, but he had fitted multi-plug for charging items. Note also the untidy wiring, various rusty items and screen that's been repaired by fiberglass:
Some road rash on the fairing:
Bent footpeg and shift lever. There is also some rust on the sub-frame:
Relatively new chain that is starting to rust as it hasn't been kept lubricated:
Faded taillight, rusted grab rail and torn seat:
Dented and scratched exhaust:
Broken vfr400 mirrors:
Fiberglass repairs to the fairing:
I'm going to be starting with the mechanical's first and when those are sorted moving on to the cosmetics. I've already had the radiator welded and pressure tested, as it was leaking when I bought the bike, next up will be to figure out why the fan isn't switching on.
Hope you enjoy the show
Conrad
'88 FZR1000 Genesis
- GreyImport
- Level 2.0
- Posts: 233
- Joined: Fri Jun 22, 2012 3:07 am
- Location: Sunny Australia
Re: Genesis rebuild
A rusty christmas tree
Sounds like u have the right plan ....unfortunately when the cosmetics are neglected the mechanicals are usually the same!
looks in pretty good shape in general though.
Good luck with it
Sounds like u have the right plan ....unfortunately when the cosmetics are neglected the mechanicals are usually the same!
looks in pretty good shape in general though.
Good luck with it
1990 FZR250R 3LN1
1977 Triumph Bonneville 750 T140V
http://2fiftycc.com/index.php
EMAIL: greyimport@2fiftycc.com
LiteTek Carburettor Seal Kits
http://www.litetek.co/index.html
1977 Triumph Bonneville 750 T140V
http://2fiftycc.com/index.php
EMAIL: greyimport@2fiftycc.com
LiteTek Carburettor Seal Kits
http://www.litetek.co/index.html
Re: Genesis rebuild
many people have started with less so you're not in horrible shape. I used to be overly concerned with the cosmetic details of mine until I realized I was spending perfectly good riding days painting things.
Re: Genesis rebuild
Hi will,
I have to agree I would rather be riding than painting, but by the same token I do want something that looks presentable.
It definetly won't be a show bike, but I am planning a custom spray job after I've made it reliable.
I have to agree I would rather be riding than painting, but by the same token I do want something that looks presentable.
It definetly won't be a show bike, but I am planning a custom spray job after I've made it reliable.
'88 FZR1000 Genesis
Re: Genesis rebuild
We are having good riding weather at the moment and I'm having lots of fun riding the bike. This means that its going to be a while before I actually get around to rebuilding the bike (Its possibly even going to be slower than the slowest build thread ).
So for now my rebuild consists of giving her a good wash and lubing the chain:
So for now my rebuild consists of giving her a good wash and lubing the chain:
'88 FZR1000 Genesis
Re: Genesis rebuild
When you are riding at part throttle, and try to accelerate with revs are below 5000, the bike bogs down. I can only describe the feeling as something akin to a turtle trying to run through peanut butter. I ordered the stage 1 factory pro carb kit, with the idea being that I would rebuild the carbs and make the bike more rideable, till I get around to tearing it down.
Silly me, never read the description properly. I never realized that it only includes the needles and not the emulsion tubes. I'm going to have to wait for these to arrive before I attempt the carb rebuild:
In the meantime Ive decided what colour scheme I'm going for. Red and white as seen on the gen 1 R1's:
Some of the other goodies I ordered for when I do rebuild her have started arriving.
Some nice valve caps:
New oil filter:
New air filter:
Vinyl to recover the seat:
Hone for when I change the rings:
New fuel filter:
Tax disk holder:
New plugs:
Fresh oil:
New mirrors:
New pedal rubber:
New fork seals:
New clutch springs:
New wheel bearings:
New float bowl gaskets and needle valve:
New steering stem bearings:
New clutch plates:
Full gasket set:
Silly me, never read the description properly. I never realized that it only includes the needles and not the emulsion tubes. I'm going to have to wait for these to arrive before I attempt the carb rebuild:
In the meantime Ive decided what colour scheme I'm going for. Red and white as seen on the gen 1 R1's:
Some of the other goodies I ordered for when I do rebuild her have started arriving.
Some nice valve caps:
New oil filter:
New air filter:
Vinyl to recover the seat:
Hone for when I change the rings:
New fuel filter:
Tax disk holder:
New plugs:
Fresh oil:
New mirrors:
New pedal rubber:
New fork seals:
New clutch springs:
New wheel bearings:
New float bowl gaskets and needle valve:
New steering stem bearings:
New clutch plates:
Full gasket set:
'88 FZR1000 Genesis
Re: Genesis rebuild
Time for a long overdue update. A couple of the other parts I ordered arrived:
These are the new eom style indicators I bought to replace those silly little oval ones:
A chain riverter:
Some new foot pegs:
Bar ends:
Clutch plates:
Some fairing bolts:
And of course, it's always interesting receiving parts from china, you never know what the instructions will say:
These are the new eom style indicators I bought to replace those silly little oval ones:
A chain riverter:
Some new foot pegs:
Bar ends:
Clutch plates:
Some fairing bolts:
And of course, it's always interesting receiving parts from china, you never know what the instructions will say:
'88 FZR1000 Genesis
Re: Genesis rebuild
This was my first attempt at recovering a seat. As you can see there are a few wrinkles. Next time I'll glue the vinyl to the foam:
Replacing the air filter provided some entertainment.As you can see the previous owner decided to DIY a k&n filter
I rebuilt the carbs using the factory pro stage 1 kit, and it made a huge difference. Gone is the mid-range flat spot I used to have. You can actually see the different profile of the needles:
I also fitted the passenger foot pegs:
After that it was time to tear it down to fix the 3rd gear:
The motor was in better condition than I expected.Aside from the 3rd gear problem, I only replaced the timing chain and clutch.everything else was well within spec.
I've put the motor back together again, and am busy painting a few things before it goes back in the frame:
Replacing the air filter provided some entertainment.As you can see the previous owner decided to DIY a k&n filter
I rebuilt the carbs using the factory pro stage 1 kit, and it made a huge difference. Gone is the mid-range flat spot I used to have. You can actually see the different profile of the needles:
I also fitted the passenger foot pegs:
After that it was time to tear it down to fix the 3rd gear:
The motor was in better condition than I expected.Aside from the 3rd gear problem, I only replaced the timing chain and clutch.everything else was well within spec.
I've put the motor back together again, and am busy painting a few things before it goes back in the frame:
'88 FZR1000 Genesis
- GreyImport
- Level 2.0
- Posts: 233
- Joined: Fri Jun 22, 2012 3:07 am
- Location: Sunny Australia
Re: Genesis rebuild
Looks like u are making good progress there
What was the problem with 3rd gear?
And u havnt checked the skin with a small dish yet?
What was the problem with 3rd gear?
And u havnt checked the skin with a small dish yet?
1990 FZR250R 3LN1
1977 Triumph Bonneville 750 T140V
http://2fiftycc.com/index.php
EMAIL: greyimport@2fiftycc.com
LiteTek Carburettor Seal Kits
http://www.litetek.co/index.html
1977 Triumph Bonneville 750 T140V
http://2fiftycc.com/index.php
EMAIL: greyimport@2fiftycc.com
LiteTek Carburettor Seal Kits
http://www.litetek.co/index.html
Re: Genesis rebuild
It would pop out of gear every time you opened the throttle in 3rd, so I had the gears undercut
'88 FZR1000 Genesis
Re: Genesis rebuild
Looking like its going to be very tidy bike when it's all finsihed. It will be very nice for you to just to get it up and running for now after all the work you've put into it so far
Can you tell me where you got the OEM style indicators from? I need one just like this to get my 400 through an MOT (it will match the good one that's still attached).
Can you tell me where you got the OEM style indicators from? I need one just like this to get my 400 through an MOT (it will match the good one that's still attached).
Re: Genesis rebuild
Duane...
Bike:
1994 Yamaha FZR 1000 EXUP
Factory Pro Stage 1 Jetting | K&N Filter | Corbin Seat | ProTek Keyless Gas Cap | GSXR Mirrors
My Thread
Cage:
2005 Saab 9-7x 5.3i Arc AWD
THE WIKI IS YOUR FRIEND
THE SEARCH IS YOUR SIGNIFICANT OTHER
USE THEM!!
Bike:
1994 Yamaha FZR 1000 EXUP
Factory Pro Stage 1 Jetting | K&N Filter | Corbin Seat | ProTek Keyless Gas Cap | GSXR Mirrors
My Thread
Cage:
2005 Saab 9-7x 5.3i Arc AWD
THE WIKI IS YOUR FRIEND
THE SEARCH IS YOUR SIGNIFICANT OTHER
USE THEM!!
Re: Genesis rebuild
I really am looking forward to riding her again, but there are still a few things that I want to get done while the engines out. On the list is painting the frame and swingarm, chainging the head, swingarm and wheel bearings.
I'm hoping it will be rideable within the next 2 weeks.
Wrt the indicators, I got the set off ebay. I must say they not bad quality at all:
http://www.ebay.com/itm/Rear-Turn-Signa ... 4aa9d6a860
I'm hoping it will be rideable within the next 2 weeks.
Wrt the indicators, I got the set off ebay. I must say they not bad quality at all:
http://www.ebay.com/itm/Rear-Turn-Signa ... 4aa9d6a860
'88 FZR1000 Genesis
-
- 100+ Posts
- Posts: 130
- Joined: Sun Nov 25, 2012 4:48 am
- Location: Santa Maria, California
- Contact:
Re: Genesis rebuild
looks nice, to do the seat its nice to have a heat gun it helps make the vinly more flexible , just dont sit the heat gun it to long, or even a blow dryer can do the job you can still fix the wrinkles..
Sal Co-Owner of SisBro Motowerkz, Santa Maria
Pacific Coast Riderz -Vice President- Santa Maria Chapter
1996 Yamaha Fzr 600
UNI Air Filter, FP 1.0, R6 header danmoto exhaust,
Orbit Chain 530 with JT Sprocket Set -1 front/+2 rear
Racetech Front suspension
Bridgestone BT-014 120/70/17 & 150/60/18
http://www.facebook.com/Salvador.Leal.Jr
http://www.youtube.com/user/KaspenOne
http://www.facebook.com/pages/Pacific-C ... 9453630808 & http://www.facebook.com/pcr805
Pacific Coast Riderz -Vice President- Santa Maria Chapter
1996 Yamaha Fzr 600
UNI Air Filter, FP 1.0, R6 header danmoto exhaust,
Orbit Chain 530 with JT Sprocket Set -1 front/+2 rear
Racetech Front suspension
Bridgestone BT-014 120/70/17 & 150/60/18
http://www.facebook.com/Salvador.Leal.Jr
http://www.youtube.com/user/KaspenOne
http://www.facebook.com/pages/Pacific-C ... 9453630808 & http://www.facebook.com/pcr805
Re: Genesis rebuild
Hi Conrad,
Thanks for the lead on the indicators (they're a perfect match for mine).
Good luck with the rest of the build.
Thanks for the lead on the indicators (they're a perfect match for mine).
Good luck with the rest of the build.