Search found 9 matches

by kurt112345
Fri Jun 17, 2016 2:08 am
Forum: Items Wanted
Topic: stock fzr1000 exhaust
Replies: 3
Views: 3114

Re: stock fzr1000 exhaust

yeah iam in the states, that is a very nice looking header. I imagine shipping would be crazy. I always thought the servos where the same but different plug good to know , at very least fab my own plug setup.
by kurt112345
Wed Jun 15, 2016 7:06 pm
Forum: Items Wanted
Topic: stock fzr1000 exhaust
Replies: 3
Views: 3114

stock fzr1000 exhaust

i have 90 fzr1000 with full vance and hines exhaust, i want to put exup back on it and dont have anything, need stock header pipe, exup servo and cables and stock muffler or slip on for stock header. thanks
by kurt112345
Sun May 01, 2016 6:35 pm
Forum: FZR1000
Topic: Coil voltage
Replies: 7
Views: 4440

Re: Coil voltage

The plug wires and plugs arent in question, the problem is when you turn key on that there is 1.5v drop from 13-13.1v at battey and 11.5v at coils. Iam under the impression they should be the same within .5v. So somthing is creating a little resistance for the coil power wire.
by kurt112345
Sun May 01, 2016 5:40 pm
Forum: FZR1000
Topic: Coil voltage
Replies: 7
Views: 4440

Re: Coil voltage

The 11.5v I was getting is with coils not plugged in red/white wire, and did check coil resistance while I was there and both within spec. Looked at diagram and chased the red/white wire around, used electrical cleaner and small diamond file to clean connectors. So far I cleaned the start switch too...
by kurt112345
Wed Apr 27, 2016 1:26 pm
Forum: FZR1000
Topic: Coil voltage
Replies: 7
Views: 4440

Coil voltage

Quick question on coil voltage, my battery has a new bike master gel battery and is 13.2v, at my coils is 11.5v. Could this create a running issue or miss? Has anyone ever done the coil relay mod that is common practice over at the GS forum, by using the original coil power wires to trigger a relay ...
by kurt112345
Tue Apr 05, 2016 2:36 am
Forum: FZR1000
Topic: 90 fzr 1000 needle ID and tune
Replies: 5
Views: 4528

Re: 90 fzr 1000 needle ID and tune

alright dang, hmmmmmm, I ordered new emulsion tubes and factory pro jet kit, when I looked at the old needles in my bike which are aluminum and 7 clip positions, the looked kinda worn one side like you can almost feel it. so with new tubes and the new jet kit and no exup, is it possible to make it o...
by kurt112345
Tue Apr 05, 2016 2:27 am
Forum: Items Wanted
Topic: 90 fzr 1000 inner fork tube
Replies: 6
Views: 3282

90 fzr 1000 inner fork tube

Looking for a clean strait inner fork tube, mine has rust pits and fork seal wont seal, thanks
by kurt112345
Sat Apr 02, 2016 2:41 am
Forum: FZR1000
Topic: 90 fzr 1000 needle ID and tune
Replies: 5
Views: 4528

Re: 90 fzr 1000 needle ID and tune

Can these bikes run good down low with out exup? obviously with proper jetting. around from idle to 4000krpm general light cruising in town?
by kurt112345
Wed Mar 30, 2016 8:00 pm
Forum: FZR1000
Topic: 90 fzr 1000 needle ID and tune
Replies: 5
Views: 4528

90 fzr 1000 needle ID and tune

Iam a new fzr owner, I posted in the introduction. I picked up a 90 fzr 1000 with 8600 miles on that obviously been sitting a long time, had carbs off put new boots on old ones just cracked apart. Did a dip on carbs get them looking great, but the bike did come with a vance and Hines super sport exh...